Users browsing this forum: 43 Guest(s)

Mark this forum read General Troubleshooting
Thread [desc] / Author			Replies	Views	Rating	Last Post
		Build plate's spring gets stuck after thighening the screws. Doesn't lower properly BadPotato	3	4,393	0 Vote(s) - 0 out of 5 in Average	07-06-2023, 01:59 AM Last Post: Nutters
		build platform doesnt raise during printing jensen	4	5,814	0 Vote(s) - 0 out of 5 in Average	02-11-2020, 08:05 AM Last Post: jensen
		Build Platform not making contact when leveling Brock	0	2,918	0 Vote(s) - 0 out of 5 in Average	01-18-2020, 09:20 PM Last Post: Brock
		Building Plate Goes Too High Up After Prints Finish Beefula	1	5,416	0 Vote(s) - 0 out of 5 in Average	05-04-2023, 03:59 PM Last Post: Katmodel
		Burn spot on LCD Elegoo Mars Tandrec	2	6,411	0 Vote(s) - 0 out of 5 in Average	09-09-2020, 09:00 AM Last Post: Tandrec
		Can't Print Rook or Other Test File eddiekendrick	1	159	0 Vote(s) - 0 out of 5 in Average	05-11-2024, 06:19 AM Last Post: Don
		Can't raise build platform mo3355	5	7,977	0 Vote(s) - 0 out of 5 in Average	02-11-2020, 06:56 AM Last Post: mo3355
		Cannot Print D20 Smushed Side? Snowmanner	1	2,454	0 Vote(s) - 0 out of 5 in Average	11-11-2020, 09:34 AM Last Post: DDLLC
		Can’t get a first print. missusliz	0	1,141	0 Vote(s) - 0 out of 5 in Average	06-25-2022, 02:58 PM Last Post: missusliz
		Chitubox and Elegoo Mars printing problem boblinux	0	1,016	0 Vote(s) - 0 out of 5 in Average	03-24-2023, 10:20 AM Last Post: boblinux
		ChituBox changes the height of layers samaia	2	4,036	1 Vote(s) - 5 out of 5 in Average	04-21-2020, 12:12 PM Last Post: samaia
		Circles are not Round [Mars 2 Pro] SHack	8	9,714	0 Vote(s) - 0 out of 5 in Average	01-07-2021, 05:30 PM Last Post: cliffyk
		Clean Tank like Print Error? Wolverine	1	1,903	0 Vote(s) - 0 out of 5 in Average	02-15-2024, 02:29 PM Last Post: hicm4
		Completely befuddled Gabee Moon	1	1,319	0 Vote(s) - 0 out of 5 in Average	09-21-2022, 05:45 AM Last Post: billtodd
		Consistent printing failure across layers sunrunner4kr	0	1,262	0 Vote(s) - 0 out of 5 in Average	07-06-2022, 01:33 AM Last Post: sunrunner4kr
		Creases in the printed model Emperorbaz	0	675	0 Vote(s) - 0 out of 5 in Average	09-29-2023, 05:14 AM Last Post: Emperorbaz
		curved prints at the base laureth	0	1,869	0 Vote(s) - 0 out of 5 in Average	12-08-2020, 03:18 AM Last Post: laureth
		Curving and Delamination FrozT	7	9,755	0 Vote(s) - 0 out of 5 in Average	02-10-2020, 01:23 AM Last Post: VDX
		Delamination and thicker layers? NVS3D	3	5,285	0 Vote(s) - 0 out of 5 in Average	09-22-2020, 05:00 PM Last Post: cliffyk
		Delay betwen layers gotre	0	1,962	0 Vote(s) - 0 out of 5 in Average	10-06-2020, 11:59 AM Last Post: gotre
Sort by: Subject Sort by: Last Post Sort by: Author Sort by: Creation Time Sort by: Rating Sort by: Replies Sort by: Views Order: Ascending Order: Descending From: Today From: 5 Days Ago From: 10 Days Ago From: 20 Days Ago From: 50 Days Ago From: 75 Days Ago From: 100 Days Ago From: The Last Year From: The Beginning