Elegoo 3D Printers Forum - Printer Mods / Add-Ons

Users browsing this forum: 4 Guest(s)

Pages (3): 1 2 3 Next »

Mark this forum read Printer Mods / Add-Ons
Thread / Author		Replies	Views	Rating [desc]	Last Post
Important Threads
	WiFi SD Card Setup admin	7	22,336	0 Vote(s) - 0 out of 5 in Average	07-04-2020, 11:41 AM Last Post: admin
	Modified Gcode to only run the cooling fan while the printer is running (Pages: 1 2 3 4 ) admin	30	66,881	3 Vote(s) - 5 out of 5 in Average	12-04-2020, 07:17 AM Last Post: cliffyk
	Z Axis Height Calibration (Pages: 1 2 3 4 ... 7 ) admin	66	163,768	2 Vote(s) - 5 out of 5 in Average	12-04-2022, 05:25 AM Last Post: hmida01
	Ethernet Enabled Printing (Support for ChiTuBox 1.4.0 + 1.5.0) (Pages: 1 2 3 4 ... 7 ) admin	60	142,519	1 Vote(s) - 5 out of 5 in Average	12-29-2023, 05:07 PM Last Post: The_Cre8r
	Z Axis Rail Calibration admin	4	12,997	1 Vote(s) - 5 out of 5 in Average	04-18-2020, 03:36 PM Last Post: Ilex
Normal Threads
	Linear Rail Upgrade obv	8	17,292	0 Vote(s) - 0 out of 5 in Average	07-05-2020, 01:00 AM Last Post: fromFDMtoSLA
	Spare Resin Vat Frameone	9	18,490	0 Vote(s) - 0 out of 5 in Average	02-10-2020, 07:24 AM Last Post: Rijsacker
	Controller Board Info BorillionStar	1	6,458	0 Vote(s) - 0 out of 5 in Average	08-13-2019, 09:36 AM Last Post: admin
	Heater? patmat2350	3	11,627	0 Vote(s) - 0 out of 5 in Average	03-24-2020, 03:41 PM Last Post: JoeDorson
	Custom G-code at end of prints? Vogelindustries	1	6,459	0 Vote(s) - 0 out of 5 in Average	10-22-2019, 01:33 AM Last Post: Roman Kornfeld
	Fan Replacement melreth	3	12,396	0 Vote(s) - 0 out of 5 in Average	10-04-2019, 02:36 AM Last Post: melreth
	Z height Spinnetti	2	7,842	0 Vote(s) - 0 out of 5 in Average	09-05-2019, 04:20 PM Last Post: Spinnetti
	Reduce Smell Ideas punkerkin	7	14,057	0 Vote(s) - 0 out of 5 in Average	03-05-2020, 06:30 AM Last Post: Jupp3
	Elegoo Plastic Resin Vats PolkCountyMike	3	8,192	0 Vote(s) - 0 out of 5 in Average	09-30-2021, 08:37 AM Last Post: keatonsgrandma
	UV-LED upgrade? djpsyc	4	15,250	0 Vote(s) - 0 out of 5 in Average	08-25-2020, 11:15 AM Last Post: cliffyk
	Lift height lmenten	2	6,186	0 Vote(s) - 0 out of 5 in Average	02-18-2020, 11:54 AM Last Post: kenzo
	Tested Add-ons for best results (Miniature Printing) Jroze88	1	4,981	0 Vote(s) - 0 out of 5 in Average	01-01-2020, 03:28 AM Last Post: VDX
	just another fume extraction Marsianer	0	4,174	0 Vote(s) - 0 out of 5 in Average	01-03-2020, 03:38 AM Last Post: Marsianer
	Parallel Matrix UV Light Mod Kit for EPAX X1 BorillionStar	2	6,073	0 Vote(s) - 0 out of 5 in Average	01-19-2020, 07:58 PM Last Post: admin
	Any way to unlock advertised build area? MDM3D	4	8,108	0 Vote(s) - 0 out of 5 in Average	02-23-2020, 04:06 PM Last Post: zemerick

Pages (3): 1 2 3 Next »

New Posts

Hot Thread (New)

Hot Thread (No New)

No New Posts

Contains Posts by You

Closed Thread

Forum Jump:

Login
Username/Email:
Password:	Lost Password?
	Remember me