Ethernet Enabled Printing (Support for ChiTuBox 1.4.0 + 1.5.0) - Printable Version +- Elegoo 3D Printers Forum (https://www.elegoomars.com/forum) +-- Forum: Elegoo Mars 3D Printer (https://www.elegoomars.com/forum/forumdisplay.php?fid=1) +--- Forum: Printer Mods / Add-Ons (https://www.elegoomars.com/forum/forumdisplay.php?fid=4) +--- Thread: Ethernet Enabled Printing (Support for ChiTuBox 1.4.0 + 1.5.0) (/showthread.php?tid=15) |
RE: Ethernet Enabled Printing (Support for ChiTuBox 1.4.0 + 1.5.0) - drglamenstein - 09-04-2019 (08-30-2019, 08:13 AM)drglamenstein Wrote: Any update on the testing? RE: Ethernet Enabled Printing (Support for ChiTuBox 1.4.0 + 1.5.0) - admin - 09-04-2019 You should be able to run just the epax ui and be good to go, I'll actually test that right now... RE: Ethernet Enabled Printing (Support for ChiTuBox 1.4.0 + 1.5.0) - admin - 09-04-2019 I just tested the Epax UI, running the latest elegoo FW and seems to work... RE: Ethernet Enabled Printing (Support for ChiTuBox 1.4.0 + 1.5.0) - drglamenstein - 09-04-2019 Thanks for checking! I'll only load - UI_3_5-MARS_EPAX.bin - update.LCD Much appreciated... RE: Ethernet Enabled Printing (Support for ChiTuBox 1.4.0 + 1.5.0) - admin - 09-05-2019 (09-04-2019, 06:26 PM)drglamenstein Wrote: Thanks for checking! dont even need to run the update.lcd, just the UI RE: Ethernet Enabled Printing (Support for ChiTuBox 1.4.0 + 1.5.0) - fips - 09-10-2019 Hello, everyone. My firmware is V4.2.16_LCD /1440x2560 /F2.0 i try to install the fpga xxx.bin but i always get the error message: error "no authorization!". i tried the release: Mars V4.2.16_LCD /1440x2560 /F2.7 and MARS EPAX NETWORK ENABLED CHITUBOX 1.4.0 + 1.5.0.zip does anyone have any idea how I can proceed to activate the network? RE: Ethernet Enabled Printing (Support for ChiTuBox 1.4.0 + 1.5.0) - serial59 - 09-11-2019 how can we remove the epax and return to normal? I tried to reset the normal firmwrae but it does not change anything because I have a print problem arrived at 6 min of print it stops alone as if I had to stop the print (09-10-2019, 11:57 PM)fips Wrote: Hello, everyone. RE: Ethernet Enabled Printing (Support for ChiTuBox 1.4.0 + 1.5.0) - stonehome - 09-17-2019 I can confirm: If you see V4.2.20.3_LCDM /1440x2560 /F2.9 you just need to print UI_3_5-MARS_EPAX.bin Please update the readme doc: Code: 4. If you see V4.2.20.3_LCDM /1440x2560 /F2.9 (GO TO PART X BELOW) RE: Ethernet Enabled Printing (Support for ChiTuBox 1.4.0 + 1.5.0) - stonehome - 09-17-2019 This is what I found regarding the mainboard . [attachment=16][attachment=19] Please confirm and/or include some pictures and/or links. RE: Ethernet Enabled Printing (Support for ChiTuBox 1.4.0 + 1.5.0) - Dicsoft - 09-27-2019 Hello, before I try to upgrade my Mars to ethernet functionality, I would like to know how to switch back to the original software in case of unforeseen problems?! Also actually I have the FW 4.2.19 /F2.7 installed! Is the instruction still valid even with a higher version number?? BR, Dirk |