Ethernet Enabled Printing (Support for ChiTuBox 1.4.0 + 1.5.0) - Printable Version +- Elegoo 3D Printers Forum (https://www.elegoomars.com/forum) +-- Forum: Elegoo Mars 3D Printer (https://www.elegoomars.com/forum/forumdisplay.php?fid=1) +--- Forum: Printer Mods / Add-Ons (https://www.elegoomars.com/forum/forumdisplay.php?fid=4) +--- Thread: Ethernet Enabled Printing (Support for ChiTuBox 1.4.0 + 1.5.0) (/showthread.php?tid=15) |
RE: Ethernet Enabled Printing (Support for ChiTuBox 1.4.0 + 1.5.0) - admin - 09-27-2019 I'll get the readme updated and add in the original Mars UI for reverting back. RE: Ethernet Enabled Printing (Support for ChiTuBox 1.4.0 + 1.5.0) - admin - 09-30-2019 Just edited the original post by adding the defualt Mars UI for reverting back RE: Ethernet Enabled Printing (Support for ChiTuBox 1.4.0 + 1.5.0) - admin - 09-30-2019 Just updated the setup files as well to correspond with the latest FW RE: Ethernet Enabled Printing (Support for ChiTuBox 1.4.0 + 1.5.0) - jangrewe - 10-04-2019 Hi, my printer has the version V4.3.1_LCDF /1440x2560 /F2.12 - any chance i can switch to the Epax FW, too? I was already planning to pretty much only use the network feature, as i can't use Octoprint like with my other printers... RE: Ethernet Enabled Printing (Support for ChiTuBox 1.4.0 + 1.5.0) - admin - 10-04-2019 It hasn't been tested yet to confirm, but most likely, just updating to the epax UI would be all that's needed. RE: Ethernet Enabled Printing (Support for ChiTuBox 1.4.0 + 1.5.0) - stonehome - 10-04-2019 Is there any tool (OctoPrint plugin) available to monitor the Mars? Edit: I found Universal-Photon-Network-Controller which is still in Alpha state but already very good. RE: Ethernet Enabled Printing (Support for ChiTuBox 1.4.0 + 1.5.0) - jangrewe - 10-04-2019 Alright, so i successfully flashed the Epax UI and indeed got the "Network" option (no surprises here, as it's just an UI option) - but when tapping it, i get always dropped back into the main menu. I thought it's maybe because there's no cable connected, so i opened my printer and found... nothing. There is simply no RJ45 jack on my controller. Looks like i got a too new revision (M09), and they dropped that component now. That probably also means there will never be an official firmware with support for it... RE: Ethernet Enabled Printing (Support for ChiTuBox 1.4.0 + 1.5.0) - ignacmc - 10-11-2019 Mine is an M09 and has Ethernet Port. I received it from Amazon Spain just a week ago RE: Ethernet Enabled Printing (Support for ChiTuBox 1.4.0 + 1.5.0) - artejoya - 10-12-2019 Mine's printing now. As soon as it finishes (and I clean up), I'm going to check if my motherboard has the ethernet connector. It's new, got me home last Tuesday, also from amazon Spain. RE: Ethernet Enabled Printing (Support for ChiTuBox 1.4.0 + 1.5.0) - artejoya - 10-13-2019 Mine has ethernet conector, I'm sorry @jangrewe |