+- Elegoo 3D Printers Forum (https://www.elegoomars.com/forum)
+-- Forum: Elegoo Saturn 4K / 8K 3D Printer (https://www.elegoomars.com/forum/forumdisplay.php?fid=51)
+--- Forum: Firmware Updates (https://www.elegoomars.com/forum/forumdisplay.php?fid=53)
+--- Thread: Which Firmeware is the right one .... (/showthread.php?tid=812)
Which Firmeware is the right one .... - Tom_LP - 04-20-2021
Hello,
after many researches i successful start with printing on a Saturn. First thinks are running good, but lets find out how we can things better....
One of the thinks that a "computer enthusiast" will do : update to the latest version - but stop... there are 3 Versions of updates (20210402).
It seams depending on the used/build in screen (PJ L/PJ V5/TM).
hmmm - i searched and searched, but i cant figure out how i find my used screen. My current version of Firmeware ends with "/ F2.22".
There a few questions like mine, but no answers....
Have someone a glue into the right direction ?
kr Tom
RE: Which Firmeware is the right one .... - cliffyk - 04-20-2021
Have you seen this page at Elegoo's support site?
RE: Which Firmeware is the right one .... - Tom_LP - 04-21-2021
(04-20-2021, 06:24 PM)cliffyk Wrote: Have you seen this page at Elegoo's support site?off course - but it do not cover my issue - from the downloaded 3 "possible" updates, which one would be the right one
they only cover the "right firmware for the right printer and do not cross update between different printers" .... OK - checked, but how can i double check i have the right display (for the downloaded updates seams to be):
- ELEGOO SATUNR Firmware (PJ L Screen) 20210402.zip
- ELEGOO SATUNR Firmware (PJ V5 Screen) 20210401.zip
- ELEGOO SATUNR Firmware (TM Screen) 20210401.zip
)Again - i cant figure out which display is currently installed, and i can't believe they want a disassembly from the screen
Any hints ?
kr Tom
i make a screenshot from the "newer" Update instructions (no direct link
)i attached it to this post ...
kr Tom
RE: Which Firmeware is the right one .... - cliffyk - 04-21-2021
It is vague & incomplete. I've had pretty good responses from Elegoo support (3dp@elegoo.com), have you contacted them as to how to determine what LCD you have?
RE: Which Firmeware is the right one .... - Tom_LP - 04-21-2021
(04-21-2021, 03:00 PM)cliffyk Wrote: It is vague & incomplete. I've had pretty good responses from Elegoo support (3dp@elegoo.com), have you contacted them as to how to determine what LCD you have?
thx for up-voting the support from elegoo. My experience with supports in general are not so tingly
I wrote them - finger crossing to get a answer
kr Tom
RE: Which Firmeware is the right one .... - cliffyk - 04-22-2021
Keep in mind that they are in China, 15 hour time difference...
RE: Which Firmeware is the right one .... - Tom_LP - 04-22-2021
oh lord - that´s impressive. I got a answer
My current firmware ends with ".../ F2.22" and it seams that this is the "initial type of LCD screen". So my update-file should be the "PJ L..."-Firmware.
I attached a picture where you can investigate in deep which screen is built-in. On the cable is labeled the type of the screen....
kr Tom
RE: Which Firmeware is the right one .... - cliffyk - 04-23-2021
As I said, I have found them to be responsive and helpful...
RE: Which Firmeware is the right one .... - MrKekson - 06-23-2021
Hey. I have the pj089y2v1 screen, what firmware should i use?
RE: Which Firmeware is the right one .... - DashingRogue - 06-26-2021
Adding to this thread. I just got the Saturn, and I wanted to update the fw. Does anyone have any idea which FW to use? My printer shows: V4.3.19_LCDZ /3840X2400 /F2.18. I have already sent a message to support, but I am afraid that since it is Saturday afternoon, I may not get an answer until Monday at best. Thanks.