Thread Rating:
  • 1 Vote(s) - 5 Average
Control Printer via UART
#10
I can see the confusion. I one of the pictures, I'm powering the CBD from the 5V ping on the Pi. In practice, the Pi is powered from the buck converter and only TX|RX|GND are connected to the CBD. The CBD id being power as usual via the DC PSU.
Reply


Messages In This Thread
Control Printer via UART - by fips - 09-30-2019, 04:10 PM
RE: Control Printer via UART - by admin - 09-30-2019, 05:14 PM
RE: Control Printer via UART - by fips - 10-01-2019, 12:23 AM
RE: Control Printer via UART - by upright_animal - 12-04-2019, 02:06 PM
RE: Control Printer via UART - by fips - 01-06-2020, 07:24 PM
RE: Control Printer via UART - by revnull - 02-15-2020, 05:08 PM
RE: Control Printer via UART - by fips - 02-18-2020, 06:11 PM
RE: Control Printer via UART - by revnull - 02-23-2020, 07:56 AM
RE: Control Printer via UART - by fips - 03-01-2020, 07:47 AM
RE: Control Printer via UART - by revnull - 03-03-2020, 07:18 PM
RE: Control Printer via UART - by 0xDEADBEEF - 03-09-2020, 02:51 AM
RE: Control Printer via UART - by EMRosa - 03-20-2020, 09:41 PM
RE: Control Printer via UART - by dadwarf - 06-01-2020, 06:34 AM
RE: Control Printer via UART - by dadwarf - 06-03-2020, 09:23 AM
RE: Control Printer via UART - by dadwarf - 06-06-2020, 05:39 AM
RE: Control Printer via UART - by dadwarf - 06-07-2020, 08:41 AM
RE: Control Printer via UART - by fcobcn - 06-07-2020, 04:02 PM
RE: Control Printer via UART - by dadwarf - 06-08-2020, 12:49 AM
RE: Control Printer via UART - by revnull - 10-09-2020, 05:07 PM
RE: Control Printer via UART - by EMRosa - 10-10-2020, 06:42 AM
RE: Control Printer via UART - by l9o - 10-11-2020, 09:50 AM
RE: Control Printer via UART - by fab1o978 - 10-21-2020, 03:47 AM
RE: Control Printer via UART - by bob_the_vampire - 11-08-2020, 07:12 PM
RE: Control Printer via UART - by l9o - 11-08-2020, 07:33 PM
RE: Control Printer via UART - by bob_the_vampire - 11-09-2020, 10:15 AM
RE: Control Printer via UART - by bob_the_vampire - 11-09-2020, 03:53 PM
RE: Control Printer via UART - by l9o - 11-09-2020, 08:10 PM
RE: Control Printer via UART - by cliffyk - 11-09-2020, 04:37 PM
RE: Control Printer via UART - by bob_the_vampire - 11-09-2020, 06:19 PM
RE: Control Printer via UART - by bob_the_vampire - 11-10-2020, 05:29 PM

Forum Jump:


Users browsing this thread: 1 Guest(s)