Elegoo 3D Printers Forum › Elegoo Mars 3D Printer › Firmware Updates v
V4.3.1_LCDF /1440x2560 /F2.12

 
Thread Rating:
  • 0 Vote(s) - 0 Average
Thread Modes
V4.3.1_LCDF /1440x2560 /F2.12
fromFDMtoSLA Away
Member
***
Posts: 238
Threads: 10
Joined: Dec 2019
Reputation: 8
#11
01-16-2020, 01:40 AM (This post was last modified: 01-16-2020, 01:53 AM by fromFDMtoSLA.)
OK, will search again for the link - as i remeber it was in the reprap-forum

in my opinion: without the firmware, we are fixed to buy a spare mainboard at Elegoo,
but the board is a standard Chitu-Board (hope to get it cheaper from a other seller)
Find
Reply


Messages In This Thread
V4.3.1_LCDF /1440x2560 /F2.12 - by jangrewe - 10-04-2019, 03:58 AM
RE: V4.3.1_LCDF /1440x2560 /F2.12 - by parsec - 10-24-2019, 02:18 AM
RE: V4.3.1_LCDF /1440x2560 /F2.12 - by jangrewe - 10-24-2019, 03:00 AM
RE: V4.3.1_LCDF /1440x2560 /F2.12 - by parsec - 10-24-2019, 03:20 AM
RE: V4.3.1_LCDF /1440x2560 /F2.12 - by Vegaserik - 11-17-2019, 08:34 PM
RE: V4.3.1_LCDF /1440x2560 /F2.12 - by grwarlock - 11-18-2019, 08:06 PM
RE: V4.3.1_LCDF /1440x2560 /F2.12 - by Boban - 12-17-2019, 07:46 AM
RE: V4.3.1_LCDF /1440x2560 /F2.12 - by jangrewe - 12-17-2019, 08:34 AM
RE: V4.3.1_LCDF /1440x2560 /F2.12 - by jangrewe - 01-15-2020, 03:27 PM
RE: V4.3.1_LCDF /1440x2560 /F2.12 - by fromFDMtoSLA - 01-16-2020, 01:40 AM
RE: V4.3.1_LCDF /1440x2560 /F2.12 - by lexthore - 02-28-2020, 07:37 AM
RE: V4.3.1_LCDF /1440x2560 /F2.12 - by hhaddow - 07-18-2020, 10:52 AM
RE: V4.3.1_LCDF /1440x2560 /F2.12 - by cliffyk - 07-18-2020, 04:03 PM
RE: V4.3.1_LCDF /1440x2560 /F2.12 - by pozzy - 11-24-2020, 02:49 PM
RE: V4.3.1_LCDF /1440x2560 /F2.12 - by cliffyk - 11-24-2020, 07:04 PM
RE: V4.3.1_LCDF /1440x2560 /F2.12 - by cliffyk - 11-27-2020, 11:35 AM

Forum Jump:


Users browsing this thread: 1 Guest(s)