Greetings,
I have elegoo mars for 1 month, no problem printing for the past month.
Now, I have a problem printing.
Some models lacks a limb.
![[Image: 106269356_265564621202501_60887428670983...e=5F1E6047]](https://scontent-cdt1-1.xx.fbcdn.net/v/t1.0-9/106269356_265564621202501_608874286709835670_o.jpg?_nc_cat=105&_nc_sid=730e14&_nc_ohc=NlAhD7mfgEgAX_itxZh&_nc_ht=scontent-cdt1-1.xx&oh=e6c72d6b4b2fec3124f90afd465261d0&oe=5F1E6047)
![[Image: 106091088_265564611202502_19160990869210...e=5F1E7398]](https://scontent-cdg2-1.xx.fbcdn.net/v/t1.0-9/106091088_265564611202502_191609908692109019_o.jpg?_nc_cat=107&_nc_sid=730e14&_nc_ohc=Kp5QEpkRYFUAX81zwEC&_nc_ht=scontent-cdg2-1.xx&oh=8e4b45938f0c7bec449036d5615a3084&oe=5F1E7398)
So, I change the resin, clean the bath and I adjust the axe Z with elegoo menu and a paper.
I have changed the support from thin to medium.
Now, I print another time with some models and I only have two of them. No resin polymerised in the bath and only two are well printed. The other are nowhere !
I
![[Image: 74614901_265564584535838_607270078751762...e=5F1C6704]](https://scontent-cdt1-1.xx.fbcdn.net/v/t1.0-9/74614901_265564584535838_6072700787517620895_o.jpg?_nc_cat=101&_nc_sid=730e14&_nc_ohc=pnfutuulrFwAX-f74yr&_nc_ht=scontent-cdt1-1.xx&oh=eb7646b94a9e81562959544c0a44b781&oe=5F1C6704)
These is exposition time :
Mayer height 0.05
Bottom layer count : 8
Exposure time : 8
Bottom exposure time : 60
Bottom lift distance : 5 mm
Lifting distance : 5mm
Lifting speed : 65 mm/s
Retract speed : 150 mm
Resin : elegoo grey.
Thank you for your support.
I have elegoo mars for 1 month, no problem printing for the past month.
Now, I have a problem printing.
Some models lacks a limb.
![[Image: 106269356_265564621202501_60887428670983...e=5F1E6047]](https://scontent-cdt1-1.xx.fbcdn.net/v/t1.0-9/106269356_265564621202501_608874286709835670_o.jpg?_nc_cat=105&_nc_sid=730e14&_nc_ohc=NlAhD7mfgEgAX_itxZh&_nc_ht=scontent-cdt1-1.xx&oh=e6c72d6b4b2fec3124f90afd465261d0&oe=5F1E6047)
![[Image: 106091088_265564611202502_19160990869210...e=5F1E7398]](https://scontent-cdg2-1.xx.fbcdn.net/v/t1.0-9/106091088_265564611202502_191609908692109019_o.jpg?_nc_cat=107&_nc_sid=730e14&_nc_ohc=Kp5QEpkRYFUAX81zwEC&_nc_ht=scontent-cdg2-1.xx&oh=8e4b45938f0c7bec449036d5615a3084&oe=5F1E7398)
So, I change the resin, clean the bath and I adjust the axe Z with elegoo menu and a paper.
I have changed the support from thin to medium.
Now, I print another time with some models and I only have two of them. No resin polymerised in the bath and only two are well printed. The other are nowhere !
I
![[Image: 74614901_265564584535838_607270078751762...e=5F1C6704]](https://scontent-cdt1-1.xx.fbcdn.net/v/t1.0-9/74614901_265564584535838_6072700787517620895_o.jpg?_nc_cat=101&_nc_sid=730e14&_nc_ohc=pnfutuulrFwAX-f74yr&_nc_ht=scontent-cdt1-1.xx&oh=eb7646b94a9e81562959544c0a44b781&oe=5F1C6704)
These is exposition time :
Mayer height 0.05
Bottom layer count : 8
Exposure time : 8
Bottom exposure time : 60
Bottom lift distance : 5 mm
Lifting distance : 5mm
Lifting speed : 65 mm/s
Retract speed : 150 mm
Resin : elegoo grey.
Thank you for your support.