Users browsing this forum: 52 Guest(s)

Mark this forum read General Troubleshooting
Thread [desc] / Author			Replies	Views	Rating	Last Post
		problem with uniform horizontal lines Lobo09	5	8,829	0 Vote(s) - 0 out of 5 in Average	01-08-2021, 07:26 PM Last Post: Lobo09
		problème impression jomx3	0	3,956	0 Vote(s) - 0 out of 5 in Average	08-30-2020, 11:36 AM Last Post: jomx3
		Problems with Saturn 3 12k, stops printing Gonart	0	1,373	0 Vote(s) - 0 out of 5 in Average	12-02-2023, 12:44 PM Last Post: Gonart
		Problems with the Z-axis (Pages: 1 2 ) yaqwsx	15	36,590	0 Vote(s) - 0 out of 5 in Average	07-08-2022, 01:17 PM Last Post: FrozenBubble
		Reach Printer through VPN schwummelwummel	0	594	0 Vote(s) - 0 out of 5 in Average	11-17-2023, 09:58 AM Last Post: schwummelwummel
		Red File/Half prints MadDane	2	8,282	0 Vote(s) - 0 out of 5 in Average	08-11-2020, 03:55 AM Last Post: cliffyk
		Replaced LED Screen Does not do exposure test newt1869	9	12,407	0 Vote(s) - 0 out of 5 in Average	08-27-2020, 02:11 PM Last Post: Gauntfield
		Resin curing in the middle with no object there. Alienfrog	7	8,580	0 Vote(s) - 0 out of 5 in Average	03-29-2021, 09:15 AM Last Post: cliffyk
		resolution of the sliced file does not match screen-1440 a-guillotine	9	31,116	0 Vote(s) - 0 out of 5 in Average	01-06-2023, 07:19 PM Last Post: Jay_D
		rings printed out in a bigger size? majorabm	1	2,541	0 Vote(s) - 0 out of 5 in Average	03-09-2021, 01:07 AM Last Post: cliffyk
		ROOK not printing fieldsg22	3	5,819	1 Vote(s) - 5 out of 5 in Average	07-13-2020, 05:10 PM Last Post: cliffyk
		Rook print almost perfect Muzzy	6	7,192	0 Vote(s) - 0 out of 5 in Average	02-19-2022, 01:42 AM Last Post: Muzzy
		Saturn - Deep lines on 3d prints tarallino	0	1,761	0 Vote(s) - 0 out of 5 in Average	07-30-2021, 12:34 PM Last Post: tarallino
		Saturn 2 squishing prints and creating unwanted bases and other fun stuff. The grim one	0	1,385	0 Vote(s) - 0 out of 5 in Average	08-19-2022, 09:19 AM Last Post: The grim one
		Saturn 2: Brittle prints 5oh86	2	2,396	0 Vote(s) - 0 out of 5 in Average	12-01-2022, 09:03 AM Last Post: 5oh86
		Saturn only print the First layers Matocs	0	789	0 Vote(s) - 0 out of 5 in Average	06-12-2023, 01:53 PM Last Post: Matocs
		saturn polarizer? gaiernorbert	2	3,139	0 Vote(s) - 0 out of 5 in Average	06-16-2023, 08:56 PM Last Post: rob12770
		Single "CLICK" noise when Homing/Printing Eddie2go	6	6,522	0 Vote(s) - 0 out of 5 in Average	08-12-2022, 07:33 AM Last Post: everettblakley
		some files not showing on printer gazzauk	0	1,021	0 Vote(s) - 0 out of 5 in Average	08-14-2022, 07:52 AM Last Post: gazzauk
		Squashed Prints after Installing Chitu FHD Mono screen and updating firmware FlaffWaffle	2	3,662	0 Vote(s) - 0 out of 5 in Average	01-02-2022, 01:07 PM Last Post: billtodd
Sort by: Subject Sort by: Last Post Sort by: Author Sort by: Creation Time Sort by: Rating Sort by: Replies Sort by: Views Order: Ascending Order: Descending From: Today From: 5 Days Ago From: 10 Days Ago From: 20 Days Ago From: 50 Days Ago From: 75 Days Ago From: 100 Days Ago From: The Last Year From: The Beginning