Users browsing this forum: 6 Guest(s)

Mark this forum read General Troubleshooting
Thread [desc] / Author			Replies	Views	Rating	Last Post
		horizontal lines in my prints Ailos81	2	3,974	0 Vote(s) - 0 out of 5 in Average	12-31-2020, 08:02 PM Last Post: cliffyk
		Horizontal lines on first layer to edge of plate Zwilnik	3	3,980	0 Vote(s) - 0 out of 5 in Average	07-23-2021, 08:15 AM Last Post: Zwilnik
		How do I reset printer to factory defaults? jCapFTW	1	11,119	0 Vote(s) - 0 out of 5 in Average	02-09-2020, 06:01 PM Last Post: jCapFTW
		Hum but no movement from buildplate arm. Sousaquatch	0	1,532	0 Vote(s) - 0 out of 5 in Average	12-11-2021, 08:24 PM Last Post: Sousaquatch
		I can't print anything Vesnik	4	5,655	0 Vote(s) - 0 out of 5 in Average	03-01-2020, 07:35 AM Last Post: fromFDMtoSLA
		Inaccurate scaling reg	7	11,364	0 Vote(s) - 0 out of 5 in Average	05-18-2020, 09:54 AM Last Post: zemerick
		Incomplete print problem.... Lackey1984	0	1,578	0 Vote(s) - 0 out of 5 in Average	06-29-2021, 10:00 AM Last Post: Lackey1984
		inept newbie probably screwed up saturn setup Taralan	0	1,634	0 Vote(s) - 0 out of 5 in Average	09-30-2021, 04:11 AM Last Post: Taralan
		Inverted and printed. Yukio Hashimoto	0	2,478	0 Vote(s) - 0 out of 5 in Average	10-29-2019, 05:25 PM Last Post: Yukio Hashimoto
		Inverted Letters - Rook first print levix	1	3,582	0 Vote(s) - 0 out of 5 in Average	10-12-2019, 03:33 PM Last Post: nico940
		is there way to set elegoo mar pro to power down after finish many hour print ? crunichie@gmail.com	1	4,355	0 Vote(s) - 0 out of 5 in Average	11-07-2020, 06:05 PM Last Post: cliffyk
		Is this normal on a print? Seaking406	2	3,884	1 Vote(s) - 5 out of 5 in Average	07-06-2020, 07:18 AM Last Post: Seaking406
		Issues with the clear translucent resin CPatrick	3	9,087	0 Vote(s) - 0 out of 5 in Average	09-26-2019, 07:52 AM Last Post: CPatrick
		large seam line in print near bed on several prints hardcak	0	1,870	0 Vote(s) - 0 out of 5 in Average	11-27-2020, 12:11 PM Last Post: hardcak
		Lasagna!need help Chry-1986	2	3,333	0 Vote(s) - 0 out of 5 in Average	01-08-2021, 10:39 AM Last Post: cliffyk
		Layer curling Dirty Kibbles	3	4,690	0 Vote(s) - 0 out of 5 in Average	10-01-2020, 12:07 PM Last Post: cliffyk
		LCD error code: T_100 L_10 seafreak62	4	7,721	0 Vote(s) - 0 out of 5 in Average	04-01-2020, 01:23 PM Last Post: seafreak62
		LCD Problems KenW	0	1,268	0 Vote(s) - 0 out of 5 in Average	08-18-2022, 09:32 AM Last Post: KenW
		LCD screen came off Dustdevl	3	8,409	0 Vote(s) - 0 out of 5 in Average	01-16-2020, 08:58 PM Last Post: Dustdevl
		LCD Screen Failing at the end Mono98	2	4,240	0 Vote(s) - 0 out of 5 in Average	07-26-2020, 09:11 PM Last Post: Mono98
Sort by: Subject Sort by: Last Post Sort by: Author Sort by: Creation Time Sort by: Rating Sort by: Replies Sort by: Views Order: Ascending Order: Descending From: Today From: 5 Days Ago From: 10 Days Ago From: 20 Days Ago From: 50 Days Ago From: 75 Days Ago From: 100 Days Ago From: The Last Year From: The Beginning