Users browsing this forum: 13 Guest(s)

Mark this forum read Printer Mods / Add-Ons
Thread [desc] / Author			Replies	Views	Rating	Last Post
Important Threads
		Ethernet Enabled Printing (Support for ChiTuBox 1.4.0 + 1.5.0) (Pages: 1 2 3 4 ... 7 ) admin	60	144,698	1 Vote(s) - 5 out of 5 in Average	12-29-2023, 05:07 PM Last Post: The_Cre8r
		Modified Gcode to only run the cooling fan while the printer is running (Pages: 1 2 3 4 ) admin	30	68,043	3 Vote(s) - 5 out of 5 in Average	12-04-2020, 07:17 AM Last Post: cliffyk
		WiFi SD Card Setup admin	7	22,559	0 Vote(s) - 0 out of 5 in Average	07-04-2020, 11:41 AM Last Post: admin
		Z Axis Height Calibration (Pages: 1 2 3 4 ... 7 ) admin	66	166,211	2 Vote(s) - 5 out of 5 in Average	12-04-2022, 05:25 AM Last Post: hmida01
		Z Axis Rail Calibration admin	4	13,170	1 Vote(s) - 5 out of 5 in Average	04-18-2020, 03:36 PM Last Post: Ilex
Normal Threads
		25mm fan + active charcoal filter + higher leveling feet Greg	6	21,396	0 Vote(s) - 0 out of 5 in Average	05-29-2020, 02:37 PM Last Post: Greg
		Adding PAUSE commands in (.ctb) print file? zslane	0	2,252	0 Vote(s) - 0 out of 5 in Average	05-05-2021, 10:41 AM Last Post: zslane
		Any way to unlock advertised build area? MDM3D	4	8,257	0 Vote(s) - 0 out of 5 in Average	02-23-2020, 04:06 PM Last Post: zemerick
		change screen for a monocrhome?¿ ebsigma	0	1,996	0 Vote(s) - 0 out of 5 in Average	03-05-2022, 08:27 AM Last Post: ebsigma
		Change Screen Saver Image benji	3	6,229	0 Vote(s) - 0 out of 5 in Average	05-09-2020, 08:27 AM Last Post: fromFDMtoSLA
		Complete Printer Overhaul ft. NanoDLP deadwood83	5	12,355	1 Vote(s) - 5 out of 5 in Average	03-26-2020, 07:37 PM Last Post: Dodger
		Control Printer via UART (Pages: 1 2 3 4 ) fips	30	47,695	1 Vote(s) - 5 out of 5 in Average	04-27-2023, 04:40 AM Last Post: xmodpt
		Controller Board Info BorillionStar	1	6,560	0 Vote(s) - 0 out of 5 in Average	08-13-2019, 09:36 AM Last Post: admin
		CTB files not showing up on printer andrewfg59	0	1,180	0 Vote(s) - 0 out of 5 in Average	04-18-2023, 12:51 AM Last Post: andrewfg59
		Custom G-code at end of prints? Vogelindustries	1	6,539	0 Vote(s) - 0 out of 5 in Average	10-22-2019, 01:33 AM Last Post: Roman Kornfeld
		Custom UI Packs dprossner	1	3,548	0 Vote(s) - 0 out of 5 in Average	01-05-2022, 07:15 PM Last Post: meltyface
		Disable Beeping benji	5	10,103	0 Vote(s) - 0 out of 5 in Average	05-09-2020, 11:14 AM Last Post: benji
		Elegoo / ChiTu control boards Dodger	0	4,153	0 Vote(s) - 0 out of 5 in Average	03-26-2020, 07:24 PM Last Post: Dodger
		Elegoo Mars 3 Pro Turn Fans Off When Not Printing Narey	0	1,828	0 Vote(s) - 0 out of 5 in Average	09-21-2022, 10:21 AM Last Post: Narey
		Elegoo Plastic Resin Vats PolkCountyMike	3	8,340	0 Vote(s) - 0 out of 5 in Average	09-30-2021, 08:37 AM Last Post: keatonsgrandma
Sort by: Subject Sort by: Last Post Sort by: Author Sort by: Creation Time Sort by: Rating Sort by: Replies Sort by: Views Order: Ascending Order: Descending From: Today From: 5 Days Ago From: 10 Days Ago From: 20 Days Ago From: 50 Days Ago From: 75 Days Ago From: 100 Days Ago From: The Last Year From: The Beginning