| Reputation Report for admin | ||||||||||||||||||||||
| Summary | ||||||||||||||||||||||
|
||||||||||||||||||||||
| Comments | ||||||||||||||||||||||
|
moguro (
0
) - Last updated 06-02-2022, 07:41 PM Rating given for admin's post in Modified Gcode to only run the cooling fan while the printer is running Positive (+1): [No comment] |
||||||||||||||||||||||
|
Steve.Wilson (
0
) - Last updated 03-11-2020, 12:18 PM Rating given for admin's post in Latest Mars Firmware Release - V4.2.19_LCDM /1440x2560 /F2.7 Positive (+1): [No comment] |
||||||||||||||||||||||
|
C3Dsnod (
1
) - Last updated 02-16-2020, 06:20 PM Rating given for admin's post in Layer / Print Time Calculator Positive (+1): [No comment] |
||||||||||||||||||||||
|
DolanDolan (
0
) - Last updated 02-03-2020, 07:09 AM Rating given for admin's post in Layer / Print Time Calculator Positive (+1): [No comment] |
||||||||||||||||||||||
|
C3Dsnod (
1
) - Last updated 11-24-2019, 10:16 AM Rating given for admin's post in Good luck with the new Forum. Positive (+1): [No comment] |
||||||||||||||||||||||
|
vanuden66 (
0
) - Last updated 11-08-2019, 01:31 PM Rating given for admin's post in Z Axis Height Calibration Positive (+1): [No comment] |
||||||||||||||||||||||
|
tbdad (
0
) - Last updated 10-26-2019, 01:23 PM Rating given for admin's post in Z Axis Height Calibration Positive (+1): [No comment] |
||||||||||||||||||||||
|
C3Dsnod (
1
) - Last updated 10-17-2019, 06:11 AM Rating given for admin's post in Z Axis Height Calibration Positive (+1): [No comment] |
||||||||||||||||||||||
|
dxb (
0
) - Last updated 10-16-2019, 12:05 PM Rating given for admin's post in Z Axis Height Calibration Positive (+1): [No comment] |
||||||||||||||||||||||
|
C3Dsnod (
1
) - Last updated 10-01-2019, 12:38 PM Rating given for admin's post in Alternate icons for the theme Positive (+1): [No comment] |
||||||||||||||||||||||
|
BraveToaster (
0
) - Last updated 09-14-2019, 01:30 AM Rating given for admin's post in Modified Gcode to only run the cooling fan while the printer is running Positive (+1): [No comment] |
||||||||||||||||||||||
|
Spinnetti (
1
) - Last updated 09-06-2019, 05:53 AM Rating given for admin's post in Z height Positive (+1): [No comment] |
||||||||||||||||||||||
|
Spinnetti (
1
) - Last updated 09-05-2019, 04:19 PM Rating given for admin's post in Modified Gcode to only run the cooling fan while the printer is running Positive (+1): [No comment] |
||||||||||||||||||||||
|
PiXEL8 (
0
) - Last updated 07-21-2019, 09:24 PM Rating given for admin's post in Ethernet Enabled Printing (Support for ChiTuBox 1.4.0 + 1.5.0) Positive (+1): [No comment] |
||||||||||||||||||||||
|
obv (
0
) - Last updated 07-18-2019, 02:17 PM Rating given for admin's post in Latest Mars Firmware Release - V4.2.19_LCDM /1440x2560 /F2.7 Positive (+1): [No comment] |
||||||||||||||||||||||