Users browsing this forum: 53 Guest(s)

Mark this forum read General Troubleshooting
Thread / Author			Replies [asc]	Views	Rating	Last Post
		Only prints supports, but no model JerryBones	3	8,528	0 Vote(s) - 0 out of 5 in Average	10-09-2020, 04:49 PM Last Post: panamike
		Prints keep failing Flaggk	3	5,060	0 Vote(s) - 0 out of 5 in Average	12-09-2020, 02:01 PM Last Post: cliffyk
		Voids / gaps on the sides Antares	3	5,320	0 Vote(s) - 0 out of 5 in Average	01-17-2021, 05:32 PM Last Post: cliffyk
		Prints are failing spectacularly! Legion	3	5,508	0 Vote(s) - 0 out of 5 in Average	03-14-2021, 10:50 PM Last Post: cliffyk
		Horizontal lines on first layer to edge of plate Zwilnik	3	4,376	0 Vote(s) - 0 out of 5 in Average	07-23-2021, 08:15 AM Last Post: Zwilnik
		Build plate's spring gets stuck after thighening the screws. Doesn't lower properly BadPotato	3	4,802	0 Vote(s) - 0 out of 5 in Average	07-06-2023, 01:59 AM Last Post: Nutters
		Can't Print Rook or Other Test File eddiekendrick	3	931	0 Vote(s) - 0 out of 5 in Average	05-20-2024, 06:23 PM Last Post: eddiekendrick
		Model sink? CollinsA	2	5,211	0 Vote(s) - 0 out of 5 in Average	09-19-2019, 07:50 AM Last Post: CollinsA
		Test print error SpaceRanger	2	6,295	0 Vote(s) - 0 out of 5 in Average	09-17-2019, 06:23 AM Last Post: Badbullet
		Red File/Half prints MadDane	2	8,637	0 Vote(s) - 0 out of 5 in Average	08-11-2020, 03:55 AM Last Post: cliffyk
		heavy striations anothertime	2	5,956	0 Vote(s) - 0 out of 5 in Average	11-11-2019, 02:43 AM Last Post: anothertime
		Prints will bind to one half of build platform but not the other Fulgrima	2	5,149	0 Vote(s) - 0 out of 5 in Average	01-09-2020, 07:39 AM Last Post: Fulgrima
		Z axis will not rise. (First time set up.) Laheree	2	6,698	0 Vote(s) - 0 out of 5 in Average	01-17-2020, 09:29 AM Last Post: MouthyMattyG
		Build Plate won’t tighten Jondrew55	2	6,681	0 Vote(s) - 0 out of 5 in Average	02-15-2020, 06:24 AM Last Post: Jondrew55
		USB PORT NOT WORKING gmehal	2	4,834	0 Vote(s) - 0 out of 5 in Average	05-02-2020, 02:01 AM Last Post: raporia
		Supports cause print to fail Cvandeelen	2	4,093	0 Vote(s) - 0 out of 5 in Average	03-02-2020, 12:47 PM Last Post: Jupp3
		struts printing without models Cardinalink	2	4,197	0 Vote(s) - 0 out of 5 in Average	03-21-2020, 11:13 AM Last Post: Jupp3
		Warping issues TheKrapos	2	5,188	0 Vote(s) - 0 out of 5 in Average	09-28-2022, 05:13 AM Last Post: billtodd
		ChituBox changes the height of layers samaia	2	4,313	1 Vote(s) - 5 out of 5 in Average	04-21-2020, 12:12 PM Last Post: samaia
		Prints stop half way / FEP change Warren0101	2	5,372	0 Vote(s) - 0 out of 5 in Average	05-12-2020, 10:04 AM Last Post: Yammerton
Sort by: Subject Sort by: Last Post Sort by: Author Sort by: Creation Time Sort by: Rating Sort by: Replies Sort by: Views Order: Ascending Order: Descending From: Today From: 5 Days Ago From: 10 Days Ago From: 20 Days Ago From: 50 Days Ago From: 75 Days Ago From: 100 Days Ago From: The Last Year From: The Beginning