Users browsing this forum: 17 Guest(s)

Mark this forum read General Troubleshooting
Thread / Author [desc]			Replies	Views	Rating	Last Post
		Saturn 2: Brittle prints 5oh86	2	2,272	0 Vote(s) - 0 out of 5 in Average	12-01-2022, 09:03 AM Last Post: 5oh86
		resolution of the sliced file does not match screen-1440 a-guillotine	9	30,650	0 Vote(s) - 0 out of 5 in Average	01-06-2023, 07:19 PM Last Post: Jay_D
		Platform only goes up and down a tiny bit aidanbz	4	5,403	0 Vote(s) - 0 out of 5 in Average	03-18-2020, 02:08 PM Last Post: aidanbz
		horizontal lines in my prints Ailos81	2	3,885	0 Vote(s) - 0 out of 5 in Average	12-31-2020, 08:02 PM Last Post: cliffyk
		no power to USB Drive when plugged in to Mars Pro alexmint	2	5,137	0 Vote(s) - 0 out of 5 in Average	07-08-2020, 05:36 PM Last Post: alexmint
		Resin curing in the middle with no object there. Alienfrog	7	8,303	0 Vote(s) - 0 out of 5 in Average	03-29-2021, 09:15 AM Last Post: cliffyk
		Print Quality, Consistency, and Supports. Alpharius	2	2,932	0 Vote(s) - 0 out of 5 in Average	01-31-2022, 03:29 PM Last Post: Alpharius
		Mars 2 only printing first layer of files andywood	5	7,662	0 Vote(s) - 0 out of 5 in Average	04-02-2021, 07:18 AM Last Post: andywood
		Paper resistance is imbalanced during calibration andywood	6	7,297	0 Vote(s) - 0 out of 5 in Average	04-13-2021, 03:52 PM Last Post: cliffyk
		Touchscreen Anony Mouse	3	5,821	0 Vote(s) - 0 out of 5 in Average	02-10-2020, 05:06 AM Last Post: fromFDMtoSLA
		heavy striations anothertime	2	5,547	0 Vote(s) - 0 out of 5 in Average	11-11-2019, 02:43 AM Last Post: anothertime
		Voids / gaps on the sides Antares	3	4,559	0 Vote(s) - 0 out of 5 in Average	01-17-2021, 05:32 PM Last Post: cliffyk
		Stopping mid print (Pages: 1 2 ) archaon	10	18,580	0 Vote(s) - 0 out of 5 in Average	10-09-2023, 10:54 AM Last Post: MacDime224
		Build plate's spring gets stuck after thighening the screws. Doesn't lower properly BadPotato	3	4,250	0 Vote(s) - 0 out of 5 in Average	07-06-2023, 01:59 AM Last Post: Nutters
		Building Plate Goes Too High Up After Prints Finish Beefula	1	5,357	0 Vote(s) - 0 out of 5 in Average	05-04-2023, 03:59 PM Last Post: Katmodel
		Chitubox and Elegoo Mars printing problem boblinux	0	974	0 Vote(s) - 0 out of 5 in Average	03-24-2023, 10:20 AM Last Post: boblinux
		Supports printed, Model failed/stuck to FEP bpm5cm	1	2,990	0 Vote(s) - 0 out of 5 in Average	09-18-2020, 02:09 PM Last Post: cliffyk
		Build Platform not making contact when leveling Brock	0	2,839	0 Vote(s) - 0 out of 5 in Average	01-18-2020, 09:20 PM Last Post: Brock
		struts printing without models Cardinalink	2	3,857	0 Vote(s) - 0 out of 5 in Average	03-21-2020, 11:13 AM Last Post: Jupp3
		ELegoo Mars 2 Pro won't starting printin and starts loud hum with vibration (Pages: 1 2 ) carverebain	10	15,711	1 Vote(s) - 5 out of 5 in Average	05-13-2022, 10:17 AM Last Post: randyrue
Sort by: Subject Sort by: Last Post Sort by: Author Sort by: Creation Time Sort by: Rating Sort by: Replies Sort by: Views Order: Ascending Order: Descending From: Today From: 5 Days Ago From: 10 Days Ago From: 20 Days Ago From: 50 Days Ago From: 75 Days Ago From: 100 Days Ago From: The Last Year From: The Beginning