Elegoo 3D Printers Forum - General Troubleshooting

Users browsing this forum: 41 Guest(s)

Pages (14): « Previous 1 2 3 4 5 … 14 Next »

Mark this forum read General Troubleshooting
Thread / Author		Replies	Views	Rating	Last Post [desc]
	Mars Pro not homing ManiacStu	0	2,504	0 Vote(s) - 0 out of 5 in Average	02-13-2020, 12:20 PM Last Post: ManiacStu
	Build Plate won’t tighten Jondrew55	2	6,162	0 Vote(s) - 0 out of 5 in Average	02-15-2020, 06:24 AM Last Post: Jondrew55
	Problem with an Elegoo Mars (Pages: 1 2 ) Interceptor	18	20,744	0 Vote(s) - 0 out of 5 in Average	02-18-2020, 12:03 PM Last Post: Interceptor
	flash drive stopped working DavidBrat	0	2,119	0 Vote(s) - 0 out of 5 in Average	02-20-2020, 03:54 PM Last Post: DavidBrat
	Failed prints...it's the software (Pages: 1 2 ) Maxer	10	15,046	0 Vote(s) - 0 out of 5 in Average	02-24-2020, 08:56 AM Last Post: fromFDMtoSLA
	Model slowly delaminate from building plate * Resolved * ccarignan	0	2,255	0 Vote(s) - 0 out of 5 in Average	02-25-2020, 11:52 AM Last Post: ccarignan
	I can't print anything Vesnik	4	5,509	0 Vote(s) - 0 out of 5 in Average	03-01-2020, 07:35 AM Last Post: fromFDMtoSLA
	Build plate wouldn't rise now doesn't know where it is Jubilieus	4	7,886	0 Vote(s) - 0 out of 5 in Average	03-01-2020, 08:36 AM Last Post: Jubilieus
	Supports cause print to fail Cvandeelen	2	3,683	0 Vote(s) - 0 out of 5 in Average	03-02-2020, 12:47 PM Last Post: Jupp3
	First few layers print on plate, then nothing whimsikate	1	3,168	0 Vote(s) - 0 out of 5 in Average	03-02-2020, 01:09 PM Last Post: Jupp3
	Z axis calibration failure jorge polo	0	2,477	0 Vote(s) - 0 out of 5 in Average	03-04-2020, 09:51 AM Last Post: jorge polo
	Strange offset in some layers Cylindric	5	7,056	0 Vote(s) - 0 out of 5 in Average	03-09-2020, 05:22 PM Last Post: Cylindric
	Platform only goes up and down a tiny bit aidanbz	4	5,389	0 Vote(s) - 0 out of 5 in Average	03-18-2020, 02:08 PM Last Post: aidanbz
	struts printing without models Cardinalink	2	3,849	0 Vote(s) - 0 out of 5 in Average	03-21-2020, 11:13 AM Last Post: Jupp3
	strange printing error...any leads? tease	0	2,062	0 Vote(s) - 0 out of 5 in Average	03-23-2020, 03:30 AM Last Post: tease
	LCD error code: T_100 L_10 seafreak62	4	7,538	0 Vote(s) - 0 out of 5 in Average	04-01-2020, 01:23 PM Last Post: seafreak62
	Help Eleego Mars garita	4	5,318	0 Vote(s) - 0 out of 5 in Average	04-10-2020, 02:44 AM Last Post: garita
	ChituBox changes the height of layers samaia	2	3,922	1 Vote(s) - 5 out of 5 in Average	04-21-2020, 12:12 PM Last Post: samaia
	Mars file listing doesn't show flywithmeh	4	9,107	0 Vote(s) - 0 out of 5 in Average	04-25-2020, 07:57 AM Last Post: flywithmeh
	Holes in prints Sacai2020	3	5,359	0 Vote(s) - 0 out of 5 in Average	04-27-2020, 09:53 PM Last Post: Sahhah33

Pages (14): « Previous 1 2 3 4 5 … 14 Next »

New Posts

Hot Thread (New)

Hot Thread (No New)

No New Posts

Contains Posts by You

Closed Thread

Forum Jump:

Login
Username/Email:
Password:	Lost Password?
	Remember me