Users browsing this forum: 37 Guest(s)

Mark this forum read General Troubleshooting
Thread / Author			Replies	Views	Rating	Last Post [asc]
		M-400 error, can't update firmware for new screen Dr_CRR	0	533	0 Vote(s) - 0 out of 5 in Average	03-21-2024, 01:34 AM Last Post: Dr_CRR
		[Elegoo Mars 4 Max] Prints failing or getting huge cracks during print WizardPrinter	0	577	0 Vote(s) - 0 out of 5 in Average	02-21-2024, 04:11 PM Last Post: WizardPrinter
		Clean Tank like Print Error? Wolverine	1	1,814	0 Vote(s) - 0 out of 5 in Average	02-15-2024, 02:29 PM Last Post: hicm4
		[mars pro 3] printer doesn’t print!!! Domu	0	539	0 Vote(s) - 0 out of 5 in Average	01-22-2024, 08:07 AM Last Post: Domu
		Problems with Saturn 3 12k, stops printing Gonart	0	1,294	0 Vote(s) - 0 out of 5 in Average	12-02-2023, 12:44 PM Last Post: Gonart
		Poor quality on vertical walls KenW	0	428	0 Vote(s) - 0 out of 5 in Average	12-02-2023, 09:14 AM Last Post: KenW
		New Saturn 3 12k Does not recognise when I have set Home spooookie1	0	537	0 Vote(s) - 0 out of 5 in Average	11-28-2023, 10:02 AM Last Post: spooookie1
		Reach Printer through VPN schwummelwummel	0	558	0 Vote(s) - 0 out of 5 in Average	11-17-2023, 09:58 AM Last Post: schwummelwummel
		Stopping mid print (Pages: 1 2 ) archaon	10	18,565	0 Vote(s) - 0 out of 5 in Average	10-09-2023, 10:54 AM Last Post: MacDime224
		Creases in the printed model Emperorbaz	0	632	0 Vote(s) - 0 out of 5 in Average	09-29-2023, 05:14 AM Last Post: Emperorbaz
		Printer is making a weird sound Chloe west	0	735	0 Vote(s) - 0 out of 5 in Average	09-14-2023, 06:18 AM Last Post: Chloe west
		When is a square not a square! Fingers	0	1,190	0 Vote(s) - 0 out of 5 in Average	07-20-2023, 07:20 AM Last Post: Fingers
		Build plate's spring gets stuck after thighening the screws. Doesn't lower properly BadPotato	3	4,245	0 Vote(s) - 0 out of 5 in Average	07-06-2023, 01:59 AM Last Post: Nutters
		saturn polarizer? gaiernorbert	2	3,046	0 Vote(s) - 0 out of 5 in Average	06-16-2023, 08:56 PM Last Post: rob12770
		Saturn only print the First layers Matocs	0	754	0 Vote(s) - 0 out of 5 in Average	06-12-2023, 01:53 PM Last Post: Matocs
		Weird failure. Prints are....compressed? RBTGames	0	963	0 Vote(s) - 0 out of 5 in Average	05-19-2023, 05:17 PM Last Post: RBTGames
		Building Plate Goes Too High Up After Prints Finish Beefula	1	5,355	0 Vote(s) - 0 out of 5 in Average	05-04-2023, 03:59 PM Last Post: Katmodel
		Chitubox and Elegoo Mars printing problem boblinux	0	971	0 Vote(s) - 0 out of 5 in Average	03-24-2023, 10:20 AM Last Post: boblinux
		What does the "home" button actually do? jubuttib	0	1,279	0 Vote(s) - 0 out of 5 in Average	03-15-2023, 05:09 AM Last Post: jubuttib
		Exposure Test Fails, Saturn S, full screen with black line down center GordonVincent	0	1,217	0 Vote(s) - 0 out of 5 in Average	03-12-2023, 10:56 AM Last Post: GordonVincent
Sort by: Subject Sort by: Last Post Sort by: Author Sort by: Creation Time Sort by: Rating Sort by: Replies Sort by: Views Order: Ascending Order: Descending From: Today From: 5 Days Ago From: 10 Days Ago From: 20 Days Ago From: 50 Days Ago From: 75 Days Ago From: 100 Days Ago From: The Last Year From: The Beginning