Users browsing this forum: 43 Guest(s)

Mark this forum read General Troubleshooting
Thread / Author [asc]			Replies	Views	Rating	Last Post
		Gaps appearing in models that have printed fine in the past Tavarin	1	2,929	0 Vote(s) - 0 out of 5 in Average	09-28-2020, 11:22 PM Last Post: cliffyk
		Saturn - Deep lines on 3d prints tarallino	0	1,764	0 Vote(s) - 0 out of 5 in Average	07-30-2021, 12:34 PM Last Post: tarallino
		inept newbie probably screwed up saturn setup Taralan	0	1,640	0 Vote(s) - 0 out of 5 in Average	09-30-2021, 04:11 AM Last Post: Taralan
		Burn spot on LCD Elegoo Mars Tandrec	2	6,424	0 Vote(s) - 0 out of 5 in Average	09-09-2020, 09:00 AM Last Post: Tandrec
		Elegoo Mars C Unknown File Format issue superpants	3	10,733	0 Vote(s) - 0 out of 5 in Average	09-17-2020, 03:14 PM Last Post: Captncrunch175
		Consistent printing failure across layers sunrunner4kr	0	1,264	0 Vote(s) - 0 out of 5 in Average	07-06-2022, 01:33 AM Last Post: sunrunner4kr
		New Saturn 3 12k Does not recognise when I have set Home spooookie1	0	575	0 Vote(s) - 0 out of 5 in Average	11-28-2023, 10:02 AM Last Post: spooookie1
		Test print error SpaceRanger	2	5,983	0 Vote(s) - 0 out of 5 in Average	09-17-2019, 06:23 AM Last Post: Badbullet
		Hum but no movement from buildplate arm. Sousaquatch	0	1,545	0 Vote(s) - 0 out of 5 in Average	12-11-2021, 08:24 PM Last Post: Sousaquatch
		Cannot Print D20 Smushed Side? Snowmanner	1	2,457	0 Vote(s) - 0 out of 5 in Average	11-11-2020, 09:34 AM Last Post: DDLLC
		Another USB problem skinnygringo	4	6,086	0 Vote(s) - 0 out of 5 in Average	05-04-2020, 05:35 PM Last Post: skinnygringo
		Distorted prints Skillster	1	1,816	0 Vote(s) - 0 out of 5 in Average	11-30-2022, 04:11 AM Last Post: billtodd
		Printing cylindrical (container) not printing smoothly sideburn	0	1,393	0 Vote(s) - 0 out of 5 in Average	06-25-2021, 11:39 PM Last Post: sideburn
		Circles are not Round [Mars 2 Pro] SHack	8	9,728	0 Vote(s) - 0 out of 5 in Average	01-07-2021, 05:30 PM Last Post: cliffyk
		Mars 2 Pro touch screen Sean Chew	0	1,573	0 Vote(s) - 0 out of 5 in Average	08-19-2021, 10:29 AM Last Post: Sean Chew
		Is this normal on a print? Seaking406	2	3,895	1 Vote(s) - 5 out of 5 in Average	07-06-2020, 07:18 AM Last Post: Seaking406
		LCD error code: T_100 L_10 seafreak62	4	7,743	0 Vote(s) - 0 out of 5 in Average	04-01-2020, 01:23 PM Last Post: seafreak62
		The print detach half way to process Scote	0	2,379	0 Vote(s) - 0 out of 5 in Average	05-21-2020, 10:15 AM Last Post: Scote
		Reach Printer through VPN schwummelwummel	0	598	0 Vote(s) - 0 out of 5 in Average	11-17-2023, 09:58 AM Last Post: schwummelwummel
		ChituBox changes the height of layers samaia	2	4,044	1 Vote(s) - 5 out of 5 in Average	04-21-2020, 12:12 PM Last Post: samaia
Sort by: Subject Sort by: Last Post Sort by: Author Sort by: Creation Time Sort by: Rating Sort by: Replies Sort by: Views Order: Ascending Order: Descending From: Today From: 5 Days Ago From: 10 Days Ago From: 20 Days Ago From: 50 Days Ago From: 75 Days Ago From: 100 Days Ago From: The Last Year From: The Beginning